Mitsubishi 2,0 8V ( 4G63 SOHC ) /Regrind standard camshaft

Product number: 13.046.001U

€197.00 *

product properties

Product number: 13.046.001U
Manufacturer: Mitsubishi
Valve timing: 32/72 - 72/32
Variant: Regrinding of standard camshafts
enginetype: 2,0 8V SOHC 4G63
Application: Street
Duration: 284°
Peak timing: 110°
Valve lift: 10,9

Regrind standard camshaft Mitsubishi

Galant 2,0 8V & Space Wagon 4WD hydro

( engine 4G63 SOHC )

Applikation : Road

Duration: : 284
Peak timing: : 110
Valve lift: : 10,9
Lift at TDC: :
Valve timing: : 32/72 - 72/32
Valve clearence: :---


Some information on our camshaft program.

For a easy select, we chose four different camshaft categories. The categories show our recommendation for the application area of the car.

Road : This cam type is designed to installed into a standard produktion road car. No other modifications are necessery.

Sport : This cam type is designed for the sporty driver. We recommend the use of a ajusted chip.

Rallye : This cam type is designed for rally or slalom competition cars. We recommend the use of twin carburators or multi throttle injection systems with this cam type.

Oval track :This cam type is designed for long-time-race-, hill-climbing- and dragster- competition cars.

In principle, all camshafts are on stock and ready to be delivered.

Some camshafts require reinforced valve springs. For this, we have developed valve spring sets made of high quality materials. We ask of you to inquire the necessity of reinforced valve springs The part number under "Spring set" includes all necessary parts like bearings, spring seats etc. Single components can be supplied on inquiry.

When ordering, please state the complete vehicle data and what it will be used for, for example the road, rally, oval track, etc.

When exchanging the camshaft, be sure to also exchange all parts that come into contact with it, ( for example the dumping lever, tappets, valve adjustment plates) to ensure that the camshaft surface won\'t be damaged. We offer dumping levers made of improved materials especially for Opel-OHC-camshafts.

All camshafts are delivered with exact installation guide and data, and, if not specified differently, are to be built in like the standard camshafts.

It was our intention not to list all vehicles by name to avoid confusion. As said at the beginning, we can regrind the standard camshafts for nearly all vehicles at home and abroad, if there are no blanks available.

Erläuterung der Nockenwellen-Eigenschaften
1. Der Nockenhub kann berechnet werden, indem man den Grundkreisdurchmesser von der Nockenhöhe abzieht. Siehe Bild 1.
Es ist nicht immer möglich mit diesem Prinzip den Nockenhub zu bestimmen, da nicht immer bekannt ist an welcher Stelle die Nockenrampe beginnt und endet.
Deshalb sollte die Nockenwelle zwischen Spitzen mit einer Messuhr vermessen werden. Dabei müssen die Zentrierungen der Nockenwelle zu den Lagerstellen laufen, so dass diese keinen Höhenschlag aufweisen.

2. Da es etwas schwer zu verstehen ist, wie durch Umschleifen der Nockenhub erhöht werden kann, wird dies an dieser Stelle erklärt.
Wie in Bild 2 zu sehen ist, wird der Grundkreisdurchmesser reduziert.
Nachdem das Ventilspiel eingestellt wurde, sitzt der Nockenfolger näher an der zentralen Achse der Nockenwelle. Das Verhältnis von Nockenhöhe und Grundkreisdurchmesser hat sich verändert.


3. Die Spreizung ist der Winkelabstand der Kurbelwelle vom oberen Totpunkt des Kolbens bis zum maximalen Hub des jeweiligen Ventils.

4. Der Hub im OT (oberer Totpunkt) oder anders die Ventilüberschneidung, ist das Maß um das die Ein- und Auslassventile geöffnet sind, während sich der Kolben im oberen Totpunkt befindet.

5. Die Steuerzeiten sind die Kurbelwinkelgrade bei denen sich das Ein- und Auslassventil öffnet und schließt.
 


Seriennockenwellen Umschleifen

Bei diesen Produkten ist es notwendig , daß Sie uns Ihre Serienwellen zuschicken.
Bitte dieses Formular ausgefüllt mit den Serienwellen schicken.

PDF Auftrag-zur-Bearbeitung:-Umschleifung-von-Nockenwellen

Bei manchen Nockenwellen müssen an den Stirnseiten Zentrierbohrungen angebracht oder nachgearbeitet werden.
Hierfür berechnen wir pro Bohrung € 17,85.